Anti-corrosion spray NANOPROTECH Electronics Professional 150ml
€19.55
Tax included
5 Items
TP-06560421-EU
Saugus Atsiskaitymas
El. Bankininkystė, Grynais arba Visa - Mastercard
Nemokamas Pristatymas
Nemokamas pristatymas užsakymams nuo 59€.
Nemokamas Grąžinimas
Suteikiame 14 dienų pinigų grąžinio garantiją
Anti-corrosion spray NANOPROTECH ELECTRONICS PROFESSIONAL 150 ml
GNP Eletronics Professional protects all sensitive electronics from oxidation, humidity and short circuit. In many cases, even drowned electronics can save and restore standard functionality. While NANOPROTECH Electric is recommended for high-voltage electrical equipment, GNP Electronics Professional is ideal for low-voltage electronics. Its great advantage is that the solution is colorless and completely dry after application, so the surface is not oily and does not stick to it. Therefore, it is particularly suitable for the treatment of RC models, drones, mobile phones, cameras, electrics, el. scooters, PCs, laptops and other low voltage electronics.
How can GNP Electronics Professional spray help you?
In particular, when treating sensitive electronics, you will appreciate that Electronics Professional spray treatment does not stain the treated surface. In addition, the solution will dry out after application and will not leave oily areas where dust or other dirt will stick. When water comes into the electronics, irreparable damage can occur. GNP Electronics Professional is the first aid for drowned electronics and serves as a prevention of damage. In the event of drowning, turn the device off and disconnect completely. Apply a thin layer of solution directly to the contacts. Wait at least 15 minutes, but we recommend 24 hours. You can then fold and turn on the device. Older electronics often break contacts, most often due to their oxidation or the presence of moisture. If you encounter a similar problem, treat broken contacts with GNP Electronics Professional. Nanoparticles help clean and spill oxidized contacts to extend the life of all electronics.
Suitable for:
- RC models (controllers, regulators, servos, connectors)
- Cameras
- Mobile Phones
- Elektrokola a el. scooters
- Batteries and their contacts
- Connectors and contacts of all kinds
- PCs, laptops
- And other sensitive electronics
How to properly protect sensitive electronics?
We have written a special article for you that describes GNP Electronics Professional on your mobile phone step by step. The GNP Electronics Professional sprays protect all electronics from damage to water. The spray can be used wherever there is a risk of oxidation, where it may get wet or if you need to clean it. contacts. The solution is colorless and completely dries after application, so the treated surface will not be dyed or greasy.
Properties:
- It acts as anticorrosive and insulating protection
- Resistant to temperatures from -80 ° C to +160 ° C
- It works for up to 1 year
- Consumption: approx. 50 ml per 1 m2
- Content: 150 ml
How to use spray?
- Apply spray in well-ventilated areas and preferably with protective gloves
- Carefully shake before spraying
- Apply a fine coat (20-30 cm) on the designated surface or use the spray directly on the treated site
- Wait 10-15 minutes after application and then wipe the excess solution
GNP Eletronics Professional protects all sensitive electronics from oxidation, humidity and short circuit. In many cases, even drowned electronics can save and restore standard functionality. While NANOPROTECH Electric is recommended for high-voltage electrical equipment, GNP Electronics Professional is ideal for low-voltage electronics. Its great advantage is that the solution is colorless and completely dry after application, so the surface is not oily and does not stick to it. Therefore, it is particularly suitable for the treatment of RC models, drones, mobile phones, cameras, electrics, el. scooters, PCs, laptops and other low voltage electronics.
How can GNP Electronics Professional spray help you?
In particular, when treating sensitive electronics, you will appreciate that Electronics Professional spray treatment does not stain the treated surface. In addition, the solution will dry out after application and will not leave oily areas where dust or other dirt will stick. When water comes into the electronics, irreparable damage can occur. GNP Electronics Professional is the first aid for drowned electronics and serves as a prevention of damage. In the event of drowning, turn the device off and disconnect completely. Apply a thin layer of solution directly to the contacts. Wait at least 15 minutes, but we recommend 24 hours. You can then fold and turn on the device. Older electronics often break contacts, most often due to their oxidation or the presence of moisture. If you encounter a similar problem, treat broken contacts with GNP Electronics Professional. Nanoparticles help clean and spill oxidized contacts to extend the life of all electronics.
Suitable for:
- RC models (controllers, regulators, servos, connectors)
- Cameras
- Mobile Phones
- Elektrokola a el. scooters
- Batteries and their contacts
- Connectors and contacts of all kinds
- PCs, laptops
- And other sensitive electronics
How to properly protect sensitive electronics?
We have written a special article for you that describes GNP Electronics Professional on your mobile phone step by step. The GNP Electronics Professional sprays protect all electronics from damage to water. The spray can be used wherever there is a risk of oxidation, where it may get wet or if you need to clean it. contacts. The solution is colorless and completely dries after application, so the treated surface will not be dyed or greasy.
Properties:
- It acts as anticorrosive and insulating protection
- Resistant to temperatures from -80 ° C to +160 ° C
- It works for up to 1 year
- Consumption: approx. 50 ml per 1 m2
- Content: 150 ml
How to use spray?
- Apply spray in well-ventilated areas and preferably with protective gloves
- Carefully shake before spraying
- Apply a fine coat (20-30 cm) on the designated surface or use the spray directly on the treated site
- Wait 10-15 minutes after application and then wipe the excess solution